POINT Hardware
Firmware Feature Release POINT® Firmware 2.2.6 (GPS over ISOBUS)
PRODUCT BULLETIN Last Update: 06/24/2024 - Nick Von Muenster REVA FIRMWARE FEATURE RELEASE POINT® FIRMWARE 2.2.6 (GPS over ISOBUS) Feature Highlight Available today, the POINT® scale indicator can now interact with NMEA GPS messaging formats over ...
Enable ISOBUS PTO and GPS Detection For Use With REAP
POINT now allows both the detection of PTO status and GPS coordinates over ISOBUS. If a StarFire receiver is connected, POINT will use its position data to add Lat./Lon. coordinates to each load ticket that is recorded. To enable these features, ...
POINT ISOBUS Troubleshooting
Check to make certain that the cables are connected correctly. When connecting POINT to ISOBUS the power port on the far left should be empty. The ISOBUS harness that provides power and connects POINT to the tractor must be plugged into the DT8 port ...
MonTag Point ISO 2 Product Mount Installation Instructions
Montag ISO 2 Product Mount Installation Instructions See attached document **Please refer to Point Quick Start Guide for further instructions**
Montag Point ISO 1 Product Magnet Mount Installation Instructions
Point ISO 1 Product Magnet Mount Installation Instructions See attached document **Please refer to Point Quick Start Guide for further instructions**
Dual Scale Mode
Enabling Dual Scale Mode To enable dual scale mode the POINT must be updated to firmware 2.1.12 or later Go to "Choose Mode" and select Dual Scale, then click Select. Configuring Dual Scales Calibration Weight, Scale Capacity, Display Count, and ...
Scale-Tec POINT Livestock Settings
Lock-on Start Time Delay (in seconds) before starting the weight sampling after activation of lock-on detection. Permissible Range: 1 - 10 seconds. 2 is the recommended minimum. Increase if “weighing” starts before animal is completely on scale. ...
How to access POINT serial number
Option 1: Check the side of the box that the POINT came in. Option 2: Separate the POINT from the base adaptor and read the sticker. Option 3: Press and hold the PLAY/PAUSE button and the ZERO button both for 5 seconds. Option 4: Take a picture of ...
POINT Setup For Use With Triolet Shiftronic
Use Scale-Tec part number: 7602950 to connect POINT to the Shiftronic unit Choose Mode In the POINT mobile app, connect to the scale and tap the Choose Mode button on the Scale screen. In the Choose Mode menu, select "Shiftronic" and press submit. ...
Ordering POINT for Livestock Scales
Ordering POINT for Livestock Scales Answer the questions below to determine which conversion kit is necessary to add a POINT scale to your livestock chute. 1) Does the chute already have a scale? Yes (proceed to question 2A) No (Kit - 7300137RI & ...
POINT Troubleshooting Flowchart
Livestock Chute Scale Screens On POINT
Livestock Chute Scale Screens On POINT Setting a POINT to Chute Mode changes it's operation to better suit weighing livestock. During the process of weighing an animal, POINT will cycle through several different screens. READY The READY screen is ...
POINT Firmware Release Notes
Firmware (Version 1) Release Notes This article is a running list of release notes for the various firmware releases for the POINT Scale Display. Please refer to this article for bug fixes, feature releases, and improvements. Version 1.0.0 (Initial ...
Point Replacing OMNI Scale Head
When connecting a POINT to OMNI bars, the red J-box wire must go to the green bar wires, green to white, and white to red.
Pausing-Freezing-Holding-the Weight on Your POINT Device
WEIGHT PAUSE (HOLD) One of the basic features of the POINT device from the keypad is to provide a "Pause" in weight. This will "freeze" the scale. This feature is a handy feature for mobile scale implements, as moving from one point to another ...
Loading and Unloading -Tare- Your Scale with the POINT Keypad
Tare Mode from the POINT keypad If you don't know what the Tare mode is, you are not alone. Most people not well versed in the "scale" terminology don't understand what a Tare is. In the easiest way possible to describe a tare, it allows you to ...
Zero Balance POINT
Zeroing POINT You can operate POINT from the keypad or the mobile device. To Zero Point from the Keypad.... 1. Press and hold the Zero Button on the right side of the keypad for three seconds. A countdown will display until zero. NOTE: We ...
Power On and Off POINT
Turning on your POINT POINT requires 12vDC power to power on and operate. To Turn on POINT 1. Press the Power Button located on the left of the keypad. This is depicted in the figure below... 2. To power off POINT, press and hold the power button ...
POINT Quick Start Guide
Quick Start Guide Use this Quick Start Guide to help you get set up and running immediately. Refer to the help center for additional instructions and answers to questions..... Lets get started. Package Contents (Inside the box) Tools Required ...